wApplication Profile

Click Browse to select a predefined application profile. The profile contains details about advertised applications, as well as supported AVPs and command codes.

For further information, see Diameter Application Profile (3.0).

Routing Profile

Click Browse to select a predefined routing profile. The Profile contains details about supported hosts, listening ports, applications, and realms.

For further information, see Diameter Routing Profile (3.0).

Diameter Identity

Select Hostname to manually enter the host name (case sensitive) of this Diameter agent. In case the Origin-Host AVP has been left unconfigured, the Hostname value will be applied whenever a Diameter message is transmitted from this agent.

If SCTP is configured as server protocol, all IP addresses that are resolved from the Diameter Identity will be used as SCTP endpoints through multihoming.

Use DNS Hostname

If enabled, the Diameter Identity of the local agent is automatically set by looking up the DNS hostname that is associated with the local IP address.

Realm

Enter the Diameter realm (case sensitive) for this specific host. In case the Origin-Realm AVP has been left unconfigured, the Realm value will be applied in messages transmitted from this agent.

Listening Port

Enter the port through which the Diameter agent should "listen" for transport connections input.

When using SCTP, optionally enter the IP address of the network interface that will be used to establish a transport connection. If left unconfigured, any IP address that can be resolved from the Hostname will be selected.

Enable Diameter Too Busy

Check to enable the agent to automatically respond with DIAMETER_TOO_BUSY when the workflow is overloaded.

Maximum Workflow Queue Size(%)

Throughput Threshold (UDRs/s)

Time Between Log Entries(s)

This property tells the agent how often it should write messages to system log when it is in congestion prevention mode.

Time Between Log Entries is an integer value between 1 and 3600 seconds.

Enable Debug Events

Select this check box to enable debug mode. Useful for testing purposes.

Enable Runtime Validation

Select this check box to enable runtime validation of the Diameter messages against the command and AVP definitions in the Diameter Application profile.

The following is validated in incoming and outgoing messages:

• Occurrences and position of AVPs
• Setting of AVP flags i e M-bit and P-bit
• Setting of command flags i e Proxiable (p-bit) and Error (e-bit)

When runtime validation is selected, incoming messages that fail the validation are rejected by the Diameter Stack agent and the appropriate result code is applied in an error answer message.

Do Not Create Outgoing Connections

Select this check box to prevent the agent from actively trying to connect or reconnect if a connection is lost, with peers. When this option is checked, the agent is said to run in passive mode.

Security Profile

Enter the watchdog timer interval TWINIT. For information about TWINIT, see RFC 3539.

Socket Write Timeout

(ms)

Enter the timeout value for writing to a socket. If the write operation is blocked for longer than the timeout period, the peer will be disconnected. Write blocks may occur if the receiving peer is overloaded.

Connect Timeout (ms)

Enter the timeout value for peer connection attempts. This setting is only applicable for TCP connections.

Connect Interval (ms)

Enter the minimum time interval between connection attempts when routing messages from a workflow and the peer connection is not established. An interval timer is started at the first connection attempt; subsequent connection attempts to the same peer are then suppressed until the timer has expired.

When realm-based routing is used, the connect interval is applied only if all configured peers in the realm are down.

If you want to send connection related messages and ConnectionLost UDRs to the workflow, use the Connection Monitoring Route option to select the outgoing route for UDRs of this type. You can disable the routing of these UDRs by selecting (None), which is the default value.

The UDR types that are routed are the following:

• Capabilities_Exchange_Request (Diameter.Base)
• Capabilities_Exchange_Answer (Diameter.Base)
• Device_Watchdog_Request (Diameter.Base)
• Device_Watchdog_Response (Diameter.Base)
• ConnectionLost (Diameter)

For information on the ConnectionLost UDR, see The Diameter Base Protocol(3.0).

When the Diameter Stack agent acts as a client and cannot send a message to a target peer, the message is kept in a queue until it is sent or a timeout occurs. In case of a timeout, a DiameterErrorUDR is routed back to the workflow.

Select this check box to limit the number of messages that can be stored in the message queue, and enter the number of messages that can be queued. When the limit is exceeded, the first message in the queue is removed and handled as if a timeout has occurred. The default value is 500.

Click Configure to set specific mappings for peers that you do not want to use the default Diameter Application profile, which is set in the General tab. To configure the mappings, you enter the Peer Identity and the Diameter Application profile that you want the specified peer to use. The peer identity can be a regular expression.

The number of mappings configured is shown on the Configure button.

For each peer that connects, the specific Diameter Application profile used is chosen by first checking each Peer Profile Mapping as ordered in the Peer Profile Mappings list. If the peer identity matches the configured name or pattern, this profile is chosen. If no peer profile mapping matches, the default Diameter Application profile is used.

For Outgoing Associations 

Select this check box if you want to disable hearbeat sending for outgoing associations. 

For Incoming Associations 

Select this check box if you want to disable hearbeat sending for outgoing associations.